Learning the Basics of Installing a Bathtub
Learning the Basics of Installing a Bathtub
Blog Article
Are you trying to locate advise about How to Install a Bathtub?
Installing a tub isn't specifically brain surgery, but it does require solid plumbing, carpentry, and occasionally, tiling abilities. Changing an old bath tub with a new one is also a moderately challenging task. If the old bathtub is readily easily accessible, the task can relocate easily; if you need to open up a wall to eliminate the old tub and place the new bath tub, the task is much harder. In either situation, the job is within a residence handyman's skills, although you will certainly need an assistant to vacate the old tub as well as embeded in the brand-new one. Make sure you have actually qualified yourself for the task as well as are comfortable trying it. Rather than working with a specialist to take control of a halfway-completed project, it is better to consider using one prior to you start. Possibilities are you may need a specialist plumber to make tube links.
This post will certainly assist you set up a brand-new bathtub in your shower room if you have actually already gotten a new bathtub as well as don't require to transform the arrangement of your previous water system pipes.
Your tools and product list must make up the following:
Preparing for the Installation
First of all, the supporting framework provided with the bath must be fitted (if called for) according to the producer's directions. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is necessary to ensure that if the tap includes a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the taps device to stop stress on the tub.
Fit the flexible faucet connectors to the bottom of both taps utilizing 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet with the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you make use of all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath must now be ready to be suited its last placement.
Removing Old Touches
If you need to replace old taps with new ones as a part of your installation, then the first thing you should do is detach the water system. After doing so, switch on the faucets to drain pipes any type of water remaining in the system. The process of removing the existing faucets can be fairly bothersome due to the limited accessibility that is typically the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the taps. Have a towel ready for the remaining water that will come from the pipes. When the supply pipes have been removed, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from turning throughout this procedure. As soon as the taps have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old securing compound.
Prior to proceeding to fit the brand-new faucets, contrast the pipe links on the old faucets to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.
Setting up the Bathtub
Utilizing the two wooden boards under its feet, position the tub in the called for setting. The wood boards are handy in evenly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 tiny points.
The next objective is to make certain that the bath tub is leveled all round. This can be attained by inspecting the spirit level and also changing the feet on the bath tub till the level reviews degree.
To set up taps, fit the bottom of the furthest versatile faucet adapter to the suitable supply pipeline by making a compression join; then do the very same for the other faucet.
Activate the water system and also inspect all joints and brand-new pipework for leaks and also tighten them if required. Load the bathtub as well as also examine the overflow outlet and also the typical outlet for leaks.
Ultimately, fix the bath paneling as described in the supplier's instruction manual. Tiling and sealing around the bath tub needs to wait up until the tub has actually been utilized a minimum of when as this will certainly resolve it into its last setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic connector to prevent damages to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end provides a link to the existing supply pipes.
If you require to fit a monobloc, after that you will certainly require lowering couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, place the faucet in the installing opening in the bath/basin making sure that the washers remain in area between the tap as well as the sink. Secure the faucet in position with the producer given backnut. As soon as the faucet is safely in position, the supply pipes can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with normal tap connectors. The previous type ought to be linked to the tap ends first, tightening just by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the area where the bath fulfills the floor tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to fracture a stiff seal, causing the water to permeate the wall between the bathroom as well as the tiling, resulting in issues with dampness as well as possible leaks to the ceiling below.
You can choose from a range of coloured sealers to blend in your fixtures and also fittings. They are sold in tubes and cartridges, as well as are capable of sealing gaps as much as a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to constantly load the tub with water before sealing, to allow for the activity experienced when the tub remains in use. The sealer can split relatively very early if you do not consider this motion before securing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also conveniently readily available on the marketplace. It is suggested to fit the ceramic tiles making use of water-resistant or water resistant adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
As a keen reader about How to Install a Bathtub, I figured sharing that excerpt was beneficial. Are you aware of another person who is fascinated about the topic? Take a moment to promote it. We love reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Leading plumbing expertise for emergencies. Report this page